Red 2 Foot 4 AWG Battery Cable by Spartan Power, Positive Only

#ad
Spartan Power SINGLERED2FT4AWG #ad - Negative only. Lifetime crimp warranty! includes one 2 foot red 4 gauge cable with 5/16" lugs on both ends. Range: -55°c to +135°c dielectric strength: 500 v/mil 197 kv/cm volume resistivity: 1014 ohm-cm tensile strength: 1500 psi 141 kg/cm2 specifications: AMS-DTL-23053/5, VW-1; CSA 198, CL 1 and CL 3; UL 224, OFT New product: you asked & spartan Power has delivered! Now selling only RED cable, not a set!.

Same great ul listed battery cable used in the wildly popular Spartan Power sets. Cable features:made in the usapolyvinyl-chloride pvc insulation90°c mtw - ul & csa 105°cvoltage rating: 600 voltsvw-1 & moisture resistantROHS CompliantUL 1232/1283/1346/10269* ApprovedHeat Shrink Features:Shrink ratio: Approximately 3 to 1 at +90°C Operational temp.

Red 2 Foot 4 AWG Battery Cable by Spartan Power, Positive Only #ad - Made in the usa: all spartan Power heavy duty battery cables are made in the USA! . Need a set instead? need a positive and a negative cable set? Search for: Spartan Power 4 AWG.

More information about Spartan Power SINGLERED2FT4AWG #ad

Perko 8501DP Battery Selector Switches

#ad
Perko 8501DP #ad - Ignition Protected. Dimensions: 5-1/2" dia. 2-5/8" depth. For use with systems under 50 volts. They permit selection between batteries for starting and charging or operation of both batteries in parallel. Capacity - 250 amps continuous, 360 AMPS Intermittent. When used with non-unitized alternators, these models will interrupt the field current reducing the possibility of damage if turned "OFF" with the engine running.

For use with two or more batteries and single or dual engine systems. For use with 12, 24 and 32 Volt Marine Electrical Systems. Use two switches for dual engine systems. Built with quality materials. Capacity: 250 amps continuous, 360 Amps Intermittent.

More information about Perko 8501DP #ad


Similar products



1-2-Both-Off Battery Switch, 6V 12V 24V 48V 60V Battery Disconnect Master Cutoff Switch for Marine Boat Car RV ATV UTV Vehicle, Waterproof Heavy Duty Battery Isolator Switch, 200/1250Amps

#ad
LotFancy #ad - Widely used for car, truck, atv, travel trailer, camper, marine, Boat, utv, RV, Battery banks and other 0 up to 60V Devices; 1 Year Warranty--a replacement or refund is guaranteed. Tin-plated copper studs and nuts; Ignition-protected. Easy to install well built heavy duty Cut Off Switch: ABS plastic housing, the rear cover insulating the rear terminals against any short circuits.

Super safety: battery disconnect switch can disconnect the battery safely, eliminate any power draw from the battery when vehicle or boat is not in use Package Includes: 1 * Battery Switch 4 * Side Pads 4 * Mounting Bolts 1 * Rear Cover 100% Satisfaction Guarantee. The patented contour locking system, allowing it to be a stand alone unit, or locked together with other switches to isolate and secure the electrical system, Offering a simple economic way of separating two batteries.

1-2-Both-Off Battery Switch, 6V 12V 24V 48V 60V Battery Disconnect Master Cutoff Switch for Marine Boat Car RV ATV UTV Vehicle, Waterproof Heavy Duty Battery Isolator Switch, 200/1250Amps #ad - This battery cut shut off kill switch has four removable side plates provide access of up to 1/0 cables. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm. Specification: operation: 1-2-both-off rating: 200a dc continuous 1hr, rv, truck, marine, utv, camper, 455a dc intermittent 5 min, atv, 1250a DC Cranking 10 sec, Voltage: 6V-60V DC Stud Size: 2x3/8" 10mm Widely Applcations: Widely used for Car, Boat, Travel Trailer, Battery banks and other 0-60V Devices.

Built with quality materials. 1 years warranty. Ignition Protected.

More information about LotFancy #ad


Similar products



Blue Sea Systems m-Series Mini On-Off Battery Switch with Knob- Red

#ad
Acr Electronics 6006 #ad - Ip66 waterproof, iso 8846 and meets ABYC requirements. With removable knob. Lotfancy battery switches are the most widely compatible. Widely used for car, truck, utv, marine, camper, atv, rV, Boat, travel trailer, Battery banks and other 0 up to 60V Devices; 1 Year Warranty--a replacement or refund is guaranteed.

Single circuit on-off. Mini battery switch, mfg# 6006, Red, 300A control.500a int. 48vdc. The patented contour locking system, or locked together with other switches to isolate and secure the electrical system, allowing it to be a stand alone unit, Offering a simple economic way of separating two batteries.

Blue Sea Systems m-Series Mini On-Off Battery Switch with Knob- Red #ad - This battery cut shut off kill switch has four removable side plates provide access of up to 1/0 cables. Built with quality materials. Switches a single battery to a single load group. The rear cover insulating the rear terminals against any short circuits, ensuring that the switch meets ABYC requirements. For use with 12, 24 and 32 Volt Marine Electrical Systems.

Make before break contact design allows switching between battery banks without power interruption. Continuous rating: 300A, Maximum Voltage: 48V DC. 2.

More information about Acr Electronics 6006 #ad


Similar products



12 Circuits with Negative Bus & Cover - Blue Sea Systems ST Blade Fuse Block

#ad
Blue Seas 5026 #ad - Make before break contact design allows switching between battery banks without power interruption. Positive distribution bus with #10-32 stud. Built with quality materials. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses.

Ip66 waterproof, iso 8846 and meets ABYC requirements. St blade fuse block - 12 circuits with negative bus and cover. For use with 12, 24 and 32 Volt Marine Electrical Systems. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm.

12 Circuits with Negative Bus & Cover - Blue Sea Systems ST Blade Fuse Block #ad - Fuses sold separately. Ignition protected-safe for installation aboard gasoline powered boats. Can be used for 24-hour circuits. Accepts ato and ATC fast acting blade fuses. Lotfancy battery switches are the most widely compatible. Fuse block, atc/ato, mfg# 5026, 12 circuit, w/negative bus and cover, 32VDC max W/30Amp max per circuit & 100Amp per block.

3. 32"w x 6.

More information about Blue Seas 5026 #ad


Similar products



Blue Sea Systems 5183 100A Fuse Terminal

#ad
Acr Electronics 5183 #ad - Terminal fusecolor: yellowamperage: 100ainterrupt rating satisfies abyc requirements for DC Main circuit protection on large battery banks Ignition protected-safe for installation aboard gasoline powered boatsClear window-visual indication of blown conditionMust be used with terminal fuse block For use with 12, 24 and 32 Volt Marine Electrical Systems.

Make before break contact design allows switching between battery banks without power interruption. Built with quality materials. Visible indication of blown condition. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm.

Blue Sea Systems 5183 100A Fuse Terminal #ad - The patented contour locking system, or locked together with other switches to isolate and secure the electrical system, allowing it to be a stand alone unit, Offering a simple economic way of separating two batteries. This battery cut shut off kill switch has four removable side plates provide access of up to 1/0 cables.

Tin-plated copper studs and nuts; Ignition-protected. The rear cover insulating the rear terminals against any short circuits, ensuring that the switch meets ABYC requirements. Positive distribution bus with #10-32 stud. Accepts ato and ATC fast acting blade fuses.

More information about Acr Electronics 5183 #ad


Similar products



2 AWG 2 Gauge Single Red 3 feet w/5/16 + 3/8" Lugs Pure Copper PowerFlex Battery Inverter Cables for Solar, RV, Auto, Marine Car, Boat

#ad
WindyNation #ad - Lotfancy battery switches are the most widely compatible. Manufactured with ultra-flexible windynation Power-Flex Cable. 100% fine stranded pure COPPER cable for high amperage applications. Made in the usa by windynation inc. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm.

Can be used for 24-hour circuits. Windynation battery cables are assembled in the usa from usa manufactured windyNation PowerFlex Cable! WindyNation's battery cables are excellent for battery bank wiring, golf cart wiring, RV wiring, car stereo wiring applications, grounding cables, inverter cables, and any other application where a highly flexible pure copper conductor is required.

2 AWG 2 Gauge Single Red 3 feet w/5/16 + 3/8" Lugs Pure Copper PowerFlex Battery Inverter Cables for Solar, RV, Auto, Marine Car, Boat #ad - Requires the use of terminal fuse blocks PN 5191 or PN 2151-do not mount the fuse directly to the battery terminal. Tin-plated copper studs and nuts; Ignition-protected. Built with quality materials. The rear cover insulating the rear terminals against any short circuits, ensuring that the switch meets ABYC requirements.

Make before break contact design allows switching between battery banks without power interruption. For use with 12, 24 and 32 Volt Marine Electrical Systems. Includes one red 2 gauge cable pre-assembled with marine grade cable lugs.

More information about WindyNation #ad


Similar products



Bussmann HHX In-Line MAXI Fuse Holder

#ad
Bussmann HHX #ad - Lotfancy battery switches are the most widely compatible. Ignition protected-safe for installation aboard gasoline powered boats. Bussmann hhx in-line MAXI Fuse Holder with Cover. Never install a fuse with a larger amp rating than specified for the application, holder or wire size. Maximum amps: 60 Amps. One fuse Holder per pack.

Make before break contact design allows switching between battery banks without power interruption. Cable is sae j1127 compliant and rated for up to 600 volts from -50°C to +105°C. Pure copper cable lugs are tinned coated and utilize a closed end design for corrosion protection. Polyolefin heat shrink tubing applied to form a protective seal.

Bussmann HHX In-Line MAXI Fuse Holder #ad - Hhx in-line maxi Fuse Holder. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm. One fuse Holder per pack. Tin-plated copper studs and nuts; Ignition-protected. Built with quality materials. St blade fuse block - 12 circuits with negative bus and cover.

Leadwire: 2 x 5" / #6.

More information about Bussmann HHX #ad


Similar products



SELTERM UL Listed Marine Grade Tinned Copper Wire Lugs Heavy Duty Battery Cable Ends Eyelets Ring Terminal Connectors

#ad
SELTERM #ad - Pack of 1, 100a terminal fuse, Max voltage: 58V DC. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm. Built with quality materials. Requires the use of terminal fuse blocks PN 5191 or PN 2151-do not mount the fuse directly to the battery terminal.

10, 000 aic at 14v dc satisfies abyc requirements for DC Main circuit protection on large battery banks. Manufactured with ultra-flexible windynation Power-Flex Cable. 100% fine stranded pure COPPER cable for high amperage applications. Made in the usa by windynation inc. To ensure corrosion resistance the tin-plated lugs are salt spray tested to ASTM B 117.

SELTERM UL Listed Marine Grade Tinned Copper Wire Lugs Heavy Duty Battery Cable Ends Eyelets Ring Terminal Connectors #ad - The battery Cable lugs meet S. A. E conductivity standards and are tested to UL 486 with voltage rating of up to 600 V. Close end pad seals Out Moisture Keeping Cables Dry. One fuse Holder per pack. Positive distribution bus with #10-32 stud. Ip66 waterproof, iso 8846 and meets ABYC requirements.

More information about SELTERM #ad


Similar products



Ampper Battery Switch, 12-48 V Battery Power Cut Master Switch Disconnect Isolator for Car, Vehicle, RV and Boat On/Off

#ad
Ampper #ad - Make before break contact design allows switching between battery banks without power interruption. 2, rear cover insulates terminals against any short of circuits. No reason for return or change. 13, size: 2. 68" x 2. 68" x 3. 07". Ip66 waterproof, iso 8846 and meets ABYC requirements. Close end pad seals Out Moisture Keeping Cables Dry.

Heavy duty: abs plastic housing, rear cover insulates terminals against any short of circuits, durable made for safety use, equiped with 4 sets of bolts. Operation: on/off 2 positions, 275 a continuous at dc 12V, 455 a intermittent at dc 12v, 1250 A momentary at DC 12V. Compatible: used for dc 12 - 48 v systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.

Ampper Battery Switch, 12-48 V Battery Power Cut Master Switch Disconnect Isolator for Car, Vehicle, RV and Boat On/Off #ad - Purpose: eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely. Copper terminal stud size: 3/8" 10 mm x 2, Rv and boat, universal used for car, very easy to install, vehicle, also electrical equipment's switch. Maximum amps: 60 Amps. Can be used for 24-hour circuits.

Accepts ato and ATC fast acting blade fuses. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses.

More information about Ampper #ad


Similar products



Red & Black 12 Terminal Distribution Block -BUSBARS- With Ring Terminals - Pair

#ad
JQuad #ad - Ignition Protected. Make before break contact design allows switching between battery banks without power interruption. Operation: 1-2-both-off; rating: 200a dc continuous 1hr, 455a dc intermittent 5 min, 1250A DC Cranking 10 sec; Voltage: 6V-60V DC; Stud Size: 2x3/8" 10mm. Cable is sae j1127 compliant and rated for up to 600 volts from -50°C to +105°C.

Pure copper cable lugs are tinned coated and utilize a closed end design for corrosion protection. Polyolefin heat shrink tubing applied to form a protective seal. Hhx in-line maxi Fuse Holder. Ignition protected-safe for installation aboard gasoline powered boats. The patented contour locking system, allowing it to be a stand alone unit, or locked together with other switches to isolate and secure the electrical system, Offering a simple economic way of separating two batteries.

Red & Black 12 Terminal Distribution Block -BUSBARS- With Ring Terminals - Pair #ad - This battery cut shut off kill switch has four removable side plates provide access of up to 1/0 cables. Maximum volts: 32 V. Tin-plated copper studs and nuts; Ignition-protected. Manufactured with ultra-flexible windynation Power-Flex Cable. 100% fine stranded pure COPPER cable for high amperage applications.

Made in the usa by windynation inc.

More information about JQuad #ad


Similar products