Camco 47444 Black 5/16″ Stud 24″ Long 4-Gauge Marine Battery Cable and Lug Assembly Tinned

#ad
Camco 47444 #ad - 4 awg wire, fits 5/16" stud. Camco's type 3 boat cable wire stays ultra flexible even in the most extreme conditions. Type 3 boat cable wire stays ultra flexible even in the most extreme conditions. Heat resistant up to 105C dry. Tin plated 95% copper lugs for superior corrosion and oxidation resistance. Ul 1426 listed and manufactured to the highest ABYC standards.

Heat-resistant up to 105C dry and available in black, red, and yellow. Pre-assembled with premium marine quality tin0plated, 95%-copper lugs, each strand of individually tinned wire provides the greatest protection against corrosion and oxidation available. Camco's 24" 4awg, 5/16" stud premium marine quality battery cable wire is UL 1426 listed and manufactured to the highest ABYC standards.

More information about Camco 47444 #ad

BEP 701 Battery Switches - On-Off

#ad
Marinco 5965 #ad - This ensures that the switch meets ABYC requirements. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Bep marine battery switch test procedures UL 1107 Continuous 1 hour, intermittent 5 minutes and Cranking engine starting - 10 seconds.

The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C 212 deg F above the ambient temperature. Operation: on/off, voltage: 48v dc, 1250a dc cranking 10 sec, rating: 275a dc continuous 1hr, 455A DC Intermittent 5 min, Stud Size: 2x3/8" 10mm.

BEP 701 Battery Switches - On-Off #ad - Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches. Tin-plated copper studs and nuts. The rear cover insulating the rear terminals against any short circuits. The continuous and intermittent ratings are tested at 110% of specified ratings. This switch offers a number of unique features, allowing it to be a stand alone unit, the highlight being the patented Contour Locking System, or locked together with other switches.

All bep switches are tested Independently to this specification by a 3rd party laboratory. Three removable side plates provide access of up to 1/0 cables. The control knob can be removed by switching to an counterclockwise 45 degree position.

More information about Marinco 5965 #ad


Similar products



RENOGY 30A ANL Fuse Set w/Fuse ANL Fuse Holder + 30A ANL Fuse

#ad
Renogy RNG-SET-ANL30 #ad - Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. This product is composed of alloy and brass copper and comes with a clear protective non-conductive resistant cover. Gold/nickel plated terminal contact for corrosion resistance.

Visible through clear window to easily identify open status. For use with renogy ANL Fuse Block. Ignition protected. Rohs compliant. Tin-plated copper studs and nuts. Control knob can be removed by switching to counter-clockwise 45° position. The renogy anl fuse will protect your controller, wire, and battery from overcurrent.

RENOGY 30A ANL Fuse Set w/Fuse ANL Fuse Holder + 30A ANL Fuse #ad - This fuse set is ideal for custom installation. Ignition protected. Operation: on/off, 455a dc intermittent 5 min, voltage: 48v dc, rating: 275a dc continuous 1hr, 1250a dc cranking 10 sec, Stud Size: 2x3/8" 10mm. Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches.

This ensures the switch meets ABYC requirements.

More information about Renogy RNG-SET-ANL30 #ad


Similar products



Absolute ANL100-2, 2 Pack ANL Fuses 100 Amp Gold Plated

#ad
Absolute USA ANL100-2 #ad - Ignition protected. Absolute anl100-2 2 pack anl fuses 100 amp gold plated operation: on/off, 1250a dc cranking 10 sec, 455A DC Intermittent 5 min, rating: 275a dc continuous 1hr, Voltage: 48V DC, Stud Size: 2x3/8" 10mm. Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches.

Gold/nickel plated terminal contact for corrosion resistance. Visible through clear window to easily identify open status. For use with renogy ANL Fuse Block. Ignition protected. Rohs compliant. 2 pack anl fuse 100 Amp Gold Plated. This ensures the switch meets ABYC requirements. Tin-plated copper studs and nuts. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits.

Absolute ANL100-2, 2 Pack ANL Fuses 100 Amp Gold Plated #ad - 12 volts. 100 amp. Control knob can be removed by switching to counter-clockwise 45° position.

More information about Absolute USA ANL100-2 #ad


Similar products



RGBSIGHT 40FT 18 Gauge Single Color LED Strip Extension Cable 18AWG 2pin 2 Color Red Black Stand Wire Conductor for LED Ribbon Lamp Tape Lighting 40 Feet per Spool

#ad
RGBSIGHT INC RGBSIGHT-1032 #ad - 12 volts. Red black 2 stand wire. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Tin-plated copper studs and nuts. 40 feet / spool. For all single color LED strip light. Gold/nickel plated terminal contact for corrosion resistance.

Visible through clear window to easily identify open status. For use with renogy ANL Fuse Block. Ignition protected. Rohs compliant. 2 pack anl fuse 100 Amp Gold Plated. 18 gauge 2pin cable line core. 18 awg 2pin extension cable line red black stand wire for single color led strip lighting product: 2pin cable cord type: 18awg stranded wire jacket material: pvc flexible color: red & black rated temperature: 80°c Condition: 100% brand new never used Voltage: 5V 12V 24V 48V DC Package included: 1pc * 40 feet 18 awg red black cable Operation: on/off, 1250a dc cranking 10 sec, Voltage: 48V DC, rating: 275a dc continuous 1hr, 455A DC Intermittent 5 min, Stud Size: 2x3/8" 10mm.

RGBSIGHT 40FT 18 Gauge Single Color LED Strip Extension Cable 18AWG 2pin 2 Color Red Black Stand Wire Conductor for LED Ribbon Lamp Tape Lighting 40 Feet per Spool #ad - Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches. Ignition protected. 18awg 2pin cable. Control knob can be removed by switching to counter-clockwise 45° position.

More information about RGBSIGHT INC RGBSIGHT-1032 #ad


Similar products



Ancor Marine Grade Primary Wire and Battery Cable Black, 100 Feet, 14 AWG

#ad
Ancor 18-5070 #ad - Ancor's proprietary premium vinyl insulation stays flexible even in extreme cold and resists salt water, oil, battery acid, gasoline and ultra-violet radiation. 18 gauge 2pin cable line core. 40 feet / spool. Ancor marine grade wire is manufactured from tinned copper stranding for maximum protection against corrosion and electrolysis.

Tin-plated copper studs and nuts. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. For all single color LED strip light. They are constructed with premium vinyl insulation that is rated at 600 volts, oil, heat, 105 deg C dry and 75 deg C wet, battery acid, gasoline, stays flexible even in extreme cold -40 deg F/C and resists salt water, abrasion and ultra-violet radiation.

Ancor Marine Grade Primary Wire and Battery Cable Black, 100 Feet, 14 AWG #ad - Exceeds all ul 1426, us coast guard Charter boat CFR title 46 and ABYC standards. Ultra flexible Type 3 stranding resists fatigue due to vibration and flexing. This ensures the switch meets ABYC requirements. Gold/nickel plated terminal contact for corrosion resistance. Visible through clear window to easily identify open status.

For use with renogy ANL Fuse Block. Ignition protected.

More information about Ancor 18-5070 #ad


Similar products



Camco 47454 Red 3/8" Stud 24" Long 4-Gauge Marine Battery Cable and Lug Assembly Tinned

#ad
Camco 47454 #ad - Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Ul 1426 listed and manufactured to the highest ABYC standards. Tin-plated copper studs and nuts. They are constructed with premium vinyl insulation that is rated at 600 volts, gasoline, heat, battery acid, stays flexible even in extreme cold -40 deg F/C and resists salt water, oil, 105 deg C dry and 75 deg C wet, abrasion and ultra-violet radiation.

4 awg wire, fits 3/8" stud. Heat resistant up to 105C dry. 18 gauge 2pin cable line core. Red black 2 stand wire. This ensures the switch meets ABYC requirements. Camco's 24" 4awg, 3/8" stud premium marine quality battery cable wire is UL 1426 listed and manufactured to the highest ABYC standards. Heat-resistant up to 105C dry and available in black, red, and yellow.

Camco 47454 Red 3/8" Stud 24" Long 4-Gauge Marine Battery Cable and Lug Assembly Tinned #ad - Ultra-flexible type 3 stranding resists fatigue from vibration and provides added corrosion protection. Type 3 boat cable wire stays ultra flexible even in the most extreme conditions. Operation: on/off, 1250a dc cranking 10 sec, rating: 275a dc continuous 1hr, 455A DC Intermittent 5 min, Voltage: 48V DC, Stud Size: 2x3/8" 10mm.

Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches.

More information about Camco 47454 #ad


Similar products



Blue Sea Systems Common 150A 10-Gang BusBar with Cover

#ad
Blue Sea Systems 53614311 #ad - Tin-plated copper studs and nuts. They are constructed with premium vinyl insulation that is rated at 600 volts, gasoline, oil, battery acid, stays flexible even in extreme cold -40 deg F/C and resists salt water, heat, 105 deg C dry and 75 deg C wet, abrasion and ultra-violet radiation.4 awg wire, fits 3/8" stud.

150a common busbar with 10 screws and a cover. 40 feet / spool. Type 3 boat cable wire stays ultra flexible even in the most extreme conditions. The industry standard busbar for positive or negative power distribution Bus material - Tin platted Copper CDA 110/UnS C1100 Insert molded stainless steel studs eliminate need for securing nut and allow high torqueing electrical contact.

Blue Sea Systems Common 150A 10-Gang BusBar with Cover #ad - Ul 1426 listed and manufactured to the highest ABYC standards. Tin plated 95% copper lugs for superior corrosion and oxidation resistance. Exceeds all ul 1426, us coast guard Charter boat CFR title 46 and ABYC standards. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits.

12 volts. Max voltage: 300v aC/ 48V DC. Control knob can be removed by switching to counter-clockwise 45° position. Ultra-flexible type 3 stranding resists fatigue from vibration and provides added corrosion protection.

More information about Blue Sea Systems 53614311 #ad


Similar products



Kingopt Opt-43

#ad
Kingopt Opt-43 #ad - Tin plated 95% copper lugs for superior corrosion and oxidation resistance. Exceeds all ul 1426, us coast guard Charter boat CFR title 46 and ABYC standards. Attached Dust Cap. Ultra-flexible type 3 stranding resists fatigue from vibration and provides added corrosion protection. Heat resistant up to 105C dry.

Manufactured from individual copper strands and tinned to perform in the harshest marine environments. 40 feet / spool. Max voltage: 300v aC/ 48V DC. Reinforced polycarbonate base with tin plated pure electrical copper for maximum conductivity. 18awg 2pin cable. Ignition protected. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits.

Kingopt Opt-43 #ad - 100 amp. 12" wire. This ensures the switch meets ABYC requirements. 150a common busbar with 10 screws and a cover. Red black 2 stand wire. Control knob can be removed by switching to counter-clockwise 45° position.

More information about Kingopt Opt-43 #ad


Similar products



XtremepowerUS 158pc Electrical Wire Connection Screw Twist Connector Cap w/Spring Insert Assortment Kit

#ad
XtremepowerUS X3259 #ad - 1x#18/1x#20 max. Orange - min. Type 3 boat cable wire stays ultra flexible even in the most extreme conditions. Max voltage: 300v aC/ 48V DC. Ignition protected. Safely connect wires without soldering or electrical tape cone-shaped springs pull wires into connectors Pre-twisting wires is not required Operation: on/off, rating: 275a dc continuous 1hr, 1250a dc cranking 10 sec, 455A DC Intermittent 5 min, Voltage: 48V DC, Stud Size: 2x3/8" 10mm.

Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches. 2x#18 Max. These handy crimp connectors are color-coded by size for easy organization and fast selection. Maximum voltage: gray, blue, Orange:300; Yellow And Red: 6003x#16 40 pc. 12 volts. Exceeds all ul 1426, us coast guard Charter boat CFR title 46 and ABYC standards.

XtremepowerUS 158pc Electrical Wire Connection Screw Twist Connector Cap w/Spring Insert Assortment Kit #ad - 18awg 2pin cable. Manufactured from individual copper strands and tinned to perform in the harshest marine environments. Grey - min. Red black 2 stand wire. Pvc maxi fuse in-Line Fuse Holder.

More information about XtremepowerUS X3259 #ad


Similar products



MICTUNING LED Illuminated Automotive Blade Fuse Holder Box 10-Circuit Fuse Block with Cover

#ad
MICTUNING #ad - Materials: pc cover+ pbt base + pom latch + tin-plating Copper Applicable With: Medium Insert Blade Fuse 1A 2A 3A 5A 7. 5a 10a 15a 20a 25a 30a 35a warranty We sell it and stand behind it. 1 yr mictuning warranty and lifetime Friendly Customer Service. 4x#14/1x#18 18 pc. 2x#22 max. 1x#18/1x#20 max. 18 gauge 2pin cable line core.

Type 3 boat cable wire stays ultra flexible even in the most extreme conditions. Maximum voltage: gray, blue, Orange:300; Yellow And Red: 600 Max voltage: 300v aC/ 48V DC. Fantastic means of power distribution this is a 10-way blade fuse block that a common bus supplying power for 10 circuits at the same time, headlights, auxiliary lamp, old motor, off road cars, such as the installation for trailer brake controller, GPS, ship and others, suitable for auto, car alarm, etc.

MICTUNING LED Illuminated Automotive Blade Fuse Holder Box 10-Circuit Fuse Block with Cover #ad - Excellent protection: come with Clear PC Cover, Dustproof & Dampproof, easy to open by pressing the white latch. Continuous rating: 130A AC/ 150A DC. Input, 5. 5mm diameter Mounting Holes, max. Pvc maxi fuse in-Line Fuse Holder. It allows you to check the troubleshooting immediately, boat, making your auto more professional! Makes Something Simple!! It is a perfect kit for adding a few circuits to your auto, off-road or others if all you need is something simple.

More information about MICTUNING #ad


Similar products