AIMS Power PWRI300012120SUL 3000 Watt Pure Sine Wave Power Inverter, ETL Listed

#ad
AIMS Power PWRI300012120SUL #ad - 12 volt DC input. The inverter features a resettable 20 amp gfci outlet, along with a usb outlet and direct connect ac terminal block Key Features 3000 Watt continuous power; 6000 Watt surge 12 Volt DC input Pure sine wave GFCI Outlet AC Direct Connect Terminal Block ETL Listed and conforms to UL 458 and CSA 22.

2 no 107. 1 usb outlet 2. 1a short circuit protection on/off switch dual cooling fans thermally controlled Specifications Continuous output power: 3000 Watts Surge power capability peak power: 6000 Watts dc input / operating voltage: 9. 5-16 volts output voltage: 120 volts ac output wave form: pure sine wave Output frequency: 60 Hz Battery low voltage alarm: 9.

AIMS Power PWRI300012120SUL 3000 Watt Pure Sine Wave Power Inverter, ETL Listed #ad - 8 +/- 05 volts battery low voltage shutdown: 9. 5 v +/- 05 volts full load efficiency: 90% No load current -. 9 amps or 1. 37 amps with fan running no load minimum operating temperature: 32 degrees Fahrenheit Full load maximum operating temperature: 104 degrees Fahrenheitautomatic shutdown GFCI Reset-able AC Outlet High input voltage shutdown: 16V Low input voltage shutdown: 9.

5v +/- 05v dimensions: 21. 5" x 9.

More information about AIMS Power PWRI300012120SUL #ad

SCOSCHE X2WFH Single ANL Fuse holder

#ad
SCOSCHE X2WFH #ad - Platinum plated wiring terminals and accessories. Each audio cable is made with OFC copper for efficient signal transfer. X2 amplifier kits are designed for customers on a budget, they include everything needed to power your amplifier. All x2 products are backed by Scosche’s Lifetime Tech Support and Limited Lifetime Warranty.

X2 audio cables, blocks and amp kits are extremely reliable and a great solution for your everyday install. Anal fuse holder. Durable finish and conductivity. Easy installation of multiple amplifier Combinations. The low-profile rcA connectors feature 24k gold plated ends for optimal contact. X2 battery terminals, fuse holders and distribution blocks featured nickel plated terminals and impact resistant covers for enhanced durability.

SCOSCHE X2WFH Single ANL Fuse holder #ad - X2 audio cables and blocks are designed for great performance at a great value.

More information about SCOSCHE X2WFH #ad


Similar products



Victron BMV-712 Battery Monitor

#ad
Victron Energy MONITOR-VTBMV-S #ad - Platinum plated wiring terminals and accessories. Easy installation of multiple amplifier Combinations. Durable finish and conductivity. Next to the basic display options, the bmv-700 series also displays the state of charge, current and ampere-hours consumed, such as voltage, time to go, and power consumption in Watts.

. Complex software algorithms are needed to take all these variables into account. Anal fuse holder. The bmv-712 features an additional input which can be programmed to measure the voltage of a second battery, battery temperature or midpoint voltage. Battery "fuel-gauge", time-to-go indicator, and much more - The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery.

Built-in bluetooth communication - Monitor your batteries on Apple or Android smartphones, macbooks, tablets, and other devices. Easy to install - the shunt interrupts the negative coming off the battery bank connects to the monitor with a standard RJ12 telephone cable. Easy to program - a quick install menu and a detailed setup menu with scrolling texts assist the user when going through the various settings.

Victron BMV-712 Battery Monitor #ad - Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting. Next to the basic display options, time to go, such as voltage, and ampere-hours consumed, the BMV-700 series also displays state of charge, current, and power consumption in Watts.

More information about Victron Energy MONITOR-VTBMV-S #ad


Similar products



SELTERM 15 Pack 1/0 Gauge 1/0 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug

#ad
SELTERM #ad - Anal fuse holder. Can be Crimped or Soldered. Lugs are suitable for use with Welding Cables and Battery Cables. The copper lugs also meet S. A. E conductivity standards and are RoHS compliant. The copper eyelet connectors are rated for up to 600 volts and tested to ANSI/UL 486 standard. Heavy duty battery cable lugs from SELTERM are manufactured using industry leading manufacturing processes to guarantee a high-quality product.

Copper tubing used for producing the battery cable lugs meet ASTM B 188 electrical grade standard. Heavy duty construction for Enhanced High Temperature Durability. Platinum plated wiring terminals and accessories. Close end pad seals Out Moisture Keeping Cables Dry. Ul tested & Approved. Durable finish and conductivity.

SELTERM 15 Pack 1/0 Gauge 1/0 AWG 3/8" Stud UL Heavy Duty Copper Crimp Lugs Welding Cable Bare Copper Eyelet Lug #ad - Easy installation of multiple amplifier Combinations. Furthermore, the copper battery lugs are both UL and CUL listed to ensure optimal performance once installed. Built-in bluetooth communication - Monitor your batteries on Apple or Android smartphones, tablets, macbooks, and other devices. Easy to install - the shunt interrupts the negative coming off the battery bank connects to the monitor with a standard RJ12 telephone cable.

More information about SELTERM #ad


Similar products



Young4us 2 Pack 3/4'' Heat Shrink Tube 3:1 Adhesive-Lined Heat Shrinkable Tubing Black&RED 4Ft

#ad
Young4us 43237-2 #ad - Can be Crimped or Soldered. Shrink ratio: 3:1, round diameter: 3/4'', Length: 1. 22m4ft. These tubes are suitable for bundling, electrical insulation, mechanical protection and wire joints etc. Package content: 1 x heat shrink tubingblack 1. 22m4ft 1 x heat shrink tubingred1. 22m4ft anal fuse holder. Durable finish and conductivity.

Close end pad seals Out Moisture Keeping Cables Dry. Main color: black & red. Temperature range: -55c to +125c, beginning shrinking temperature: 70C, Completely shrinking temperature: 125C. Rated voltage: 600V. Product advantages: durable structure with fast heat-shrinkage, high heat-shrinkable ratio, strong heat-shrinkable stress.

Young4us 2 Pack 3/4'' Heat Shrink Tube 3:1 Adhesive-Lined Heat Shrinkable Tubing Black&RED 4Ft #ad - . The young4us durable heat shrink tubes are made from polyolefin, the internal layer is coated by hot-melt adhesive, which resist to harsh environment and have a high heat-shrinkable ratio of 3:1, which has satisfied bonding performance. Built-in bluetooth communication - Monitor your batteries on Apple or Android smartphones, macbooks, tablets, and other devices.

Easy to install - the shunt interrupts the negative coming off the battery bank connects to the monitor with a standard RJ12 telephone cable. Easy to program - a quick install menu and a detailed setup menu with scrolling texts assist the user when going through the various settings. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting.

More information about Young4us 43237-2 #ad


Similar products



RENOGY 5 Pair MC4 Male/ Female Solar Panel Cable Connectors Double Seal Rings for Better Waterproof Effect

#ad
Renogy 5MC4 #ad - Renogy mc4 male/female solar panel cable connectors five pairs of mc4 solar panel cable connectors ten silver plated copper rated current: 30A Wiring size range: 10, 12 AWG contact resistance: contact material: silver plated copper insulation material: PA/pc warranty information 1-year material warranty.

You can feel that they are heavier & sturdier than other similar products in the market. This is to ensure the long term durability. Description renogy cable connectors are made with highest quality materials.

More information about Renogy 5MC4 #ad


Similar products



On-Off - BEP 701 Battery Switches

#ad
Marinco 701 #ad - Shrink ratio: 3:1, round diameter: 3/4'', Length: 1. 22m4ft. Tin-plated copper studs and nuts. Platinum plated wiring terminals and accessories. Heavy duty construction for Enhanced High Temperature Durability. Three removable side plates provide access of up to 1/0 cables. Close end pad seals Out Moisture Keeping Cables Dry.

The continuous and intermittent ratings are tested at 110% of specified ratings. Durable finish and conductivity. Temperature range: -55c to +125c, beginning shrinking temperature: 70C, Completely shrinking temperature: 125C. Rated voltage: 600V. The control knob can be removed by switching to an counterclockwise 45 degree position.

On-Off - BEP 701 Battery Switches #ad - This connector is specifically designed for connecting photovoltaic solar systems with high mechanical requirements and extreme weather conditions. Bep marine battery switch test procedures UL 1107 Continuous 1 hour, intermittent 5 minutes and Cranking engine starting - 10 seconds. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits.

The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C 212 deg F above the ambient temperature. Easy installation of multiple amplifier Combinations. Anal fuse holder.

More information about Marinco 701 #ad


Similar products



WindyNation ANL Fuse Holder + ANL Fuse 2pcs 300A Fuse

#ad
WindyNation ANL-Fh-300-2 #ad - Ul tested & Approved. Renogy mc4 cable Connectors are made with highest quality materials. Use cable terminals with a 5/16" diameter or 8 mm diameter mounting hole to achieve a proper connection to the the ANL Fuse Holder mounting bolts. Ignition protected. These connectors are designed to complete a solar panel PV array, typically in parallel applications.

The windynation anl fuse holder with fuses are used in electrical systems in which the fuse is designed to burn out when the current exceeds the safe limit for the device being protected by the fuse. Includes 1pc windynation anl Fuse Holder + 2pcs ANL 300A Fuses. Rated voltage: 600V. These connectors are also waterproof and resist dust build up.

WindyNation ANL Fuse Holder + ANL Fuse 2pcs 300A Fuse #ad - This ensures the switch meets ABYC requirements. See images for technical specifications and dimensional drawings. Main color: black & red. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Temperature range: -55c to +125c, beginning shrinking temperature: 70C, Completely shrinking temperature: 125C.

Built-in bluetooth communication - Monitor your batteries on Apple or Android smartphones, tablets, macbooks, and other devices. Easy to install - the shunt interrupts the negative coming off the battery bank connects to the monitor with a standard RJ12 telephone cable.

More information about WindyNation ANL-Fh-300-2 #ad


Similar products



NEP ANL Fuse 3-Pack 400 Amp

#ad
New England Providore, LLC. ANL400-3PK #ad - Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. This ensures the switch meets ABYC requirements. Heavy duty construction for Enhanced High Temperature Durability. Operation: on/off, 455a dc intermittent 5 min, voltage: 48v dc, rating: 275a dc continuous 1hr, 1250a dc cranking 10 sec, Stud Size: 2x3/8" 10mm.

Patented contour locking System allows switch to be a stand alone unit, or locked together with other switches. Material: polyolefin. These connectors are designed to complete a solar panel PV array, typically in parallel applications. Renogy mc4 cable Connectors are made with highest quality materials. Tin-plated copper studs and nuts.

NEP ANL Fuse 3-Pack 400 Amp #ad - Main color: black & red. Use cable terminals with a 5/16" diameter or 8 mm diameter mounting hole to achieve a proper connection to the the ANL Fuse Holder mounting bolts. Built-in bluetooth communication - Monitor your batteries on Apple or Android smartphones, tablets, macbooks, and other devices. Easy to install - the shunt interrupts the negative coming off the battery bank connects to the monitor with a standard RJ12 telephone cable.

Easy to program - a quick install menu and a detailed setup menu with scrolling texts assist the user when going through the various settings.

More information about New England Providore, LLC. ANL400-3PK #ad


Similar products



Blue Sea Systems m-Series Mini On-Off Battery Switch with Knob- Red

#ad
Acr Electronics 6006 #ad - Includes 1pc windynation anl Fuse Holder + 2pcs ANL 300A Fuses. These connectors are also waterproof and resist dust build up. Ip66 waterproof, iso 8846 and meets ABYC requirements. Ul tested & Approved. Make before break contact design allows switching between battery banks without power interruption. Can be Crimped or Soldered.

Control knob can be removed by switching to counter-clockwise 45° position. Tin-plated copper studs and nuts. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Ignition protected-safe for installation aboard gasoline powered boats.

Blue Sea Systems m-Series Mini On-Off Battery Switch with Knob- Red #ad - Positions: single-circuit On-Off. Easy installation of multiple amplifier Combinations. With removable knob. Renogy mc4 cable Connectors are made with highest quality materials. These connectors are designed to complete a solar panel PV array, typically in parallel applications. Ignition protected. Temperature range: -55c to +125c, beginning shrinking temperature: 70C, Completely shrinking temperature: 125C.

Heavy duty construction for Enhanced High Temperature Durability.

More information about Acr Electronics 6006 #ad


Similar products



Link Solar Weatherproof ABS Solar Double Cable Entry Gland for All Cable Types 2mm² to 6mm² for Solar Project on Rv, Campervan, Boat

#ad
Link Solar #201809213LS #ad - These connectors are also waterproof and resist dust build up. Three removable side plates for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Link solar abs solar cable entry gland is used for the passing of cables into the Motorhome, from the Solar panel, or for use on yachts /boats for cable entry from the mast.

It can also be used for other installations and structures such as buildings, garages, sheds and other roofs Manufactured by Link Solar Anal fuse holder. Suitable for most round cables for Solar Panel, Aerial, satellite, Air conditioning, DC power, Lighting etc. Can be fixed with glue not included sikaflex 221 Sikaflex 252, 291, dicor sealant, alike or stainless steel self-tapping screws not included depending on position and sealing requirements etc.

Link Solar Weatherproof ABS Solar Double Cable Entry Gland for All Cable Types 2mm² to 6mm² for Solar Project on Rv, Campervan, Boat #ad - The whole set is within 1 ABS white box, 2 cable glands, 2 rubber seals. Close end pad seals Out Moisture Keeping Cables Dry. These connectors are designed to complete a solar panel PV array, typically in parallel applications. Ignition protected-safe for installation aboard gasoline powered boats. Heavy duty construction for Enhanced High Temperature Durability.

This ensures the switch meets ABYC requirements. Shrink ratio: 3:1, round diameter: 3/4'', Length: 1.

More information about Link Solar #201809213LS #ad


Similar products